Whether it's a cross remount, an unexpected pothole, or a rough line down the trail, the WCS Zero post will not relinquish its position. Featuring a confidence-inspiring extra-secure fore/aft bolt system, the Zero post is second-to-none in ease of installation and fit adjustment. - Fore/aft adjustment bolts for precision adjustment and secure clamping - 3D Forged 2014 Alloy - Offset: Zero - Cradle: Standard saddle rail clamp
- 3D forged from 2014 heat-treated aluminum for optimal strength to weight ratio - Race Face's triple butting design maintains strength in critical areas while reducing overall weight - The tube is anodized & shot peened for increased fatigue life - Updated Hunter head design for easy saddle installation and full adjustability - 3D forged from 2014 heat treated aluminum with triple butted mast - Thumbscrew tightening system allows quick dial-in of the saddle angle by hand - Angled clamp bolts allow easy tool access for hassle free adjustment - Rubber grommet seals the post to prevent water from entering seat tube - Accepts 7/8mm CrMo/alloy and 7/9mm carbon rails. 260g (30.9mm)
- Alloy mast with micro clamp aluminum head - One bolt adjusts tilt and fore-aft saddle position (no-offset clamp) - I-Beam single rail clamp post specific to I-Beam saddles
Sleek design and ultimate functionality of the WCS 1-Bolt seatpost are the hallmarks of Ritchey design. Single bolt-actuated side load clamp offers easy adjustability and simple security in a post that works as nicely as it looks. - 3D Forged 7050 Alloy - Available in 27.2, 30.9 and 31.6mm diameters - Available in 350 and 400mm lengths - 20mm Offset - 7x7mm saddle rail clamp included - Interchangeable clamps available for carbon rail saddles - Saddle Clamp Torque Spec: 12Nm - Finish: Blatte - 195g (27.2/350)
Bike fit is important - a bike should feel like an extension of the body, especially when dialed in. Getting just the right saddle position is second-to-none when putting out power over long miles is concerned. Ritchey Link posts offer two clamp positions for greater adjustability in dialing in the right fit. - 7050 Alloy 2pc Press Fit Head - 15mm adjustable setback - Reversible clamp for greater fore/aft adjustability - Finish: BB black
Bike fit is important. A bike should feel like an extension of the body, especially when dialed-in. Getting just the right saddle position is second-to-none when putting out power over long miles. Ritchey Link posts offer two clamp positions for greater adjustability in dialing-in the right fit. - 7050 Alloy 2pc Press Fit Head - 20mm adjustable setback - Reversible clamp for greater fore/aft adjustability - Length: 350mm
The Salsa Guide Carbon Seatpost is lightweight, durable, and supportive when you need it most. - Carbon shaft - Bonded Aluminum two-bolt head
Seatposts can be an overlooked part of the bike, but at Whisky Parts Co., everything gets the same attention to detail so your ride never suffers. Their seatposts are made from the highest quality carbon, ensuring they are durable, lightweight, and comfortable. Whether you’re remounting during a cross race or abusing them on the trail, you'll be glad you have the No.7. - Carbon shaft absorbs trail chatter - UD carbon shaft, forged aluminum head
Our new EA90 seatpost applies our patent pending ISA saddle adjustment allowing for independent seat angle and fore-aft movement, helping you refine your positioning without needing to undo your rail clamps for each minute tweak. Saddle angle is then locked in place so you have the confidence your saddle will stay put after you find your fit. - Finish: Black anodized - Weight: Zero, 295g; Setback, 268g - Head offset: 0mm, 20mm - Length: 350mm w/ 80mm min. insert - Quill size: 27.2mm - Material: EA90 alloy
Profile Design's 1/TwentyFive seatpost is the choice when you need the most aggressive position possible. 25mm setback rails ensure that your fit is totally dialed before your next ride. The 2-bolt head enables micro-adjustments to your position and eases installation. The clamps evenly distribute pressure, reducing stress on carbon saddle rails.
Pro performance post A seatpost should do one thing well — hold your seat. Our new carbon fiber Pro seatpost does that and more with a reliable 2-bolt design that lets you swap saddles with ease. Great for road or mountain use and available in a slew of diameters, lengths and offsets, this post gives you the setup versatility you've always wanted. - 2-bolt micro-adjust head mechanism offers 15 degrees of adjustment - OCLV carbon fiber shaft - Forged 6061-T6 alloy head with OCLV carbon fiber top and bottom clamps - Unique clamp shape allows for easy saddle changes - Compatible with standard and oversize carbon saddle rails - Suitable for road or mountain use
Ionic is a seatpost design featuring the sophisticated and robust, 3T–exclusive DiffLock seat clamp. Ionic–0 places the seat clamp assembly in line with the seatpost for zero setback. Many athletes seeking outright speed favor this more forward position on the bike. Some frame designers are also specifying a slacker seat tube so riders can set their bike up with an inline post, which is lighter than a setback post. The splined alloy DiffLock coupling is a highly accurate method of setting saddle angle, needing only lightweight clamping by side-mounted bolts. It is especially useful for fine adjustment of saddle setback, which can be done without impacting saddle angle. The Ionic–0 Pro is fabricated in aluminum alloy with a shot-peened, black-anodized finish. - Aluminum shaft with alloy Difflock seat clamp fits only saddles with 7mm round-section rails - Clamp Style: Standard Rails - Color: Black - Weight: 230 grams
3T's Ionic aluminum seatpost is stiff, durable, and features their Driftlock seat clamp assembly for 25mm of setback. This gives you the option of a more rearward position on today’s shorter framesets. The splined aluminum DiffLock coupling is a highly accurate method of setting saddle angle needing only lightweight clamping by side-mounted bolts. It is especially useful for fine adjustment of saddle setback, which can be done without impacting saddle angle.
Zero25 is a lightweight, universal seatpost with a twist: it’s two seatposts in one. The two clever, reversible saddle rail clamps transform the post from zero saddle setback to 25mm setback. All that’s needed is to flip the clamps from one side of the seatpost head to the other and the offset changes. No more problems with getting the wrong seatpost or needing another one when you change the type of saddle you use – it now takes 30 seconds to transform your seatpost. And the best news is that despite the double functionality, the Zero25 is even lighter than our previous seatpost. Zero25 Pro has an alloy pillar and comes in two diameters, 27.2mm and 31.6mm, and one length, 350mm.
3T's Stylus is a fresh take on the 2-bolt aluminum seatpost. The transition from the pillar to the saddle clamp assembly is a finned, rearward swoosh suggestive in shape of the classic one-bolt posts of yore. But the clamp bolts are deployed to either side of the saddle-support cradle, conferring greater stability and easier adjustment. The Stylus 25 places the seat clamp assembly with 25mm of setback for a rearward position on the bike.
- Highly tested & engineered unidirectional carbon tube offers outstanding fatigue & impact strength for a lightweight XC post - Simple, lightweight 2 bolt design permits the saddle to be installed without disassembling the head - Angled clamp bolts allow easy tool access for hassle free adjustment and tightening - The rubber seatpost grommet fully seals the post to prevent water entering your seat tube - Hunter head is suitable for most rail types 7/8mm alloy rails and 7/9mm carbon - Wide lower cradle gives extra rail support for lightweight saddle rails - Narrow upper cradle increases the amount of forward/back saddle adjustment - Tilt Adjustment 6° up 12° down with Zero offset
Trek-compatible seat mast cap Offered in white and black and a variety of lengths and offsets, the mast cap includes hardware compatible with round saddle rails only. 7x10mm carbon rail-compatible hardware sold separately. Key features: - Ultra-light carbon construction - One bolt head design offers easy fore-aft and infinite angle adjustment - Compatible with all Trek road bikes with round seat masts - 175mm and 135mm lengths - 5mm and 20mm offsets - Aluminum clamp
- Nice looking seatpost is built to the highest standards for function and ease of use - Head and shaft are made from a special high strength 2024 aluminum alloy - Two bolt head offers roughly 15 degrees of tilt adjustment - 26mm clamp setback. 320g - Made in the USA
TruVativ's carbon Noir T30 Seatpost is perfect for any XC rig. The Noir T30 Seatpost uses filament-wound tubes with a unidirectional carbon finish and all-new graphics. It’s light, it’s tough, and it can stand up to the abuses of XC riding and racing without looking worse for wear. Strategically positioned reinforcements add strength and keep the weight in check—just 235g and a dual bolt head design and titanium hardware keeps everything secure.
The redesigned Zero post offers no-slip saddle engagement and high adjustability by securing the rails with fore and aft bolts. Whether you're hitting rough singletrack or remounting in a hurry, this ensures the saddle stays exactly where you want it. - Carbon Construction with alloy clamps - Fore/aft adjustment bolts for precision adjustment and secure clamping - Zero offset - Length: 400mm - 200g (27.2x400)
The newly redesigned EC70 Seatpost takes our superlight unidirectional carbon and applies our patent pending ISA technology - Independent Saddle Adjustment - which allows for completely independent fore-aft adjustment and saddle adjustment. With the 2 pitch adjustment bolts, the saddle angle gets locked into place as if you were adjusting limit screws, and unlike single bolt designs, you get adjustability and security. Available in 20mm Setback and Zero configurations. - Finish: Matte Black UD Carbon/Matte Black Head - Weight: Zero offset, 210g; Setback offset, 223g - Head offset: 0mm; 20mm - Length: 350mm w/ 80mm min. insert - Quill size: 27.2mm - Rail clamps: 7mm round; 7mm x 9mm oval (both included) - Material: EC70 carbon
Zero25 is a lightweight, universal seatpost with a twist: it’s two seatposts in one. The two clever, reversible saddle rail clamps transform the post from zero saddle setback to 25mm setback. All that’s needed is to flip the clamps from one side of the seatpost head to the other and the offset changes. No more problems with getting the wrong seatpost or needing another one when you change the type of saddle you use – it now takes 30 seconds to transform your seatpost. And the best news is that despite the double functionality, the Zero25 is even lighter than our previous seatpost. Zero25 can handle any type of seatpost rails, from round to all oval shaped carbon rails.
Since the introduction of Zipp's line of Service Course SL components, they've had amazing success with pro-level athletes in all disciplines. While the successes have been coming, they've also drawn from riders' feedback. Zipp not only learned how and why athletes make their equipment choices, but how manufacturing methods and materials affect product performance. With new knowledge as well as new engineering, they're proud to introduce a completely redesigned Service Course SL seatpost with a carbon tube and aluminum head for better shock absorption and weight savings. - Lightweight clamping system - Updated carbon tube material
$164.00 - $175.00
Cane Creek's Thudbuster Seatpost adds comfort to any hardtail bike. Using a parallel-linkage design, the Thudbuster moves down and back at the same rate as the rear wheel moves forward and up when you hit a bump, helping you maintain control. The post and linkage is made of aluminum with Teflon coated steel bushings so you know it's built to last. And, the interchangeable elastomers (sold separately) can be easily exchanged to your preferences.
The K-Force post’s one-piece carbon fiber shaft and head are topped off with a forged alloy Minimal Top Clamp, giving a full range of adjustment and secure saddle mounting at a very low weight. There’s also the option of mounting a Shimano Di2 battery in the bottom of the post. - One piece continuous carbon fiber construction - Forged alloy Minimal Top Clamp (MTC) - UD carbon finish - Removable mounting hardware for FSA WE or Di2 battery
The all-new Highline delivers infinite adjustment, smooth feel, and easy installation for any bike. Details - Shorter insertion length to fit more bikes - Premium Trelleborg sealing - Exclusive Igus LL-glide bearings and keys - Jagwire cable and housing - Self-contained hydraulic cartridge delivers industry-leading quality and reliability - Internal routing - Quick connect mechanism for ease of cable installation - Linear actuator for quick return speed - 2-bolt standard head - Remote sold separately
The smooth and sleek design of the patented SideBinder clamp makes the Ritchey WCS Carbon 1-Bolt a sophisticated choice to finish off a performance-oriented build. The beauty of this carbon masterpiece lies in the simplicity of the design of the wide clamp head. Secured with a single 5mm bolt, this post offers ease of adjustability while relieving stress on saddle rails. - Monocoque carbon construction - Available in 27.2 & 31.6mm diameters - Available in 350 and 400mm lengths - 7x7mm saddle rail clamp included - Interchangeable clamps available for all different carbon rail sizes - Saddle clamp torque spec: 12Nm - Matte UD carbon finish - 185g (27.2/350)
The Ritchey two-bolt post, reinvented. It's now lighter, more compliant, and more versatile than ever. Patented LINK clamp works with all standard saddle rail designs as well as Ritchey Vector Evo and Selle Italia MonoLink saddles with separate adapter. LINK Carbon Posts use FlexLogic carbon layup developed for Pro Tour team bikes from Stevens, Canyon, and Scott and is 15% more vertically compliant with no loss of lateral or torsional stiffness. 15mm of offset and a reversible clamp allows for an additional 10mm of fore/aft saddle adjustment. - Monocoque Carbon Construction - Offset: 15mm - Reversible clamp allows for an additional 10mm of fore-aft saddle adjustment - Matte UD finish - 181g (27.2x300)
Bontrager's Race XXX Lite Seatpost is made of OCLV carbon for a sweet ride and minimal weight. Carbon's unique vibration damping properties smooth the road and the trail so you can go longer and harder. And, this post boasts an easy-to-use, one-bolt, infinitely-adjustable clamp.
Bontrager's Speed Concept Seatpost lets you get your fit dialed before your next triathlon or time trial. It's crafted from OCLV carbon and the one-bolt head provides simple adjustments. Different offsets allow you to customize your riding position for superior ergonomics and aerodynamics.